Lojz je napisal/-a:Ne najdem datasheet za CB5121. Je pa očitno nek step up IC. Vezje se uporablja za polnjenje 8 kosov NiMh celic (9,6V). Vtakne se pa v USB.
Na tole sem malo pozabil in spet iskal pa spet pozabil.. in zdaj sem našel nekaj podatkov...
Tvoj načrt je malenkost drugačen kot so elementi na ploščici. Med pinom 5 in 7 ni brike, pin 5 gre na GND (predvidevam, da je med pinom 8 in 5 pod čipom povezava, C4 je vezan med +B in GND in ne med +B in -B... Ampak to nima veze.
Našel sem nekaj kitajske dokumentacije in zahvaljujoč google prevajalniku je spodaj opis tega čipa, ki ima še druge oznake CJC5121 ali ASC0301. Nekaj je v slovenščini, ostalo pa v angleščini, ker je bil slo prevod na trenutke samosvoj.
Načrt je v osnovi zelo podoben tvojemu, ima tudi prikazane elemente, ki tebi manjkajo (druga led, R, C, dodatne diode....)
Za načrtom sledi opis pinov in nato tabela (
glej kitajski vir) razmerja R2/R3 in R4, v tvojem primeru R5/R6 in R4 glede na št. ni-mh baterij.
Sledi še led indikacija, ki ima 4 stanja in opisuje delovanje polnilca.
Kakega ekvivalenta znanih proizvajalcev recimo od Linear, TI, ST, Diodes ipd. na hitro nisem našel .
Upam, da ti vsaj malo koristi.
------------------
Slovenski prevod:
Funkcijski opis
Nikelj-kadmijevih nikelj-kovinskih hidridnih baterij 1 do 8 akumulatorskih baterij, vhodna napetost pri 5 V, polnilni tok baterije 8 ni manjši od 200 mA.
Delovna napetost čipa 5V, razpon napajanja 2,6V7,5V.
Čip je zasnovan z vgrajenim 10-bitnim ADC-jem za analogno-digitalno pretvorbo vzorčenih baterijskih napetosti in tokov ter sproži digitalne signale v enoto za aritmetično logiko za odkrivanje.
Rok za polnjenje 0V + -V odkrivanje.
Vgrajeni avtomatski tokovni regulator, ko se povečana napetost dvigne do maksimuma ali se vhodna napetost povleče s funkcijo trenutnega samodejnega nastavljanja, trenutna funkcija samodejnega prilagajanja toka prilagodi na največji tok.
IC lahko zazna velikost USB napajalne napetosti, ko napetost napajalne napetosti USB potegne navzdol do določenega praga, bo izklopila izhod za zaščito varnosti USB napajanja, napetost napajalne napetosti USB se dvigne in nato še naprej deluje, prag je 4.0V.
IC ima funkcijo alarmnega delovanja kratkega stika za vklop, da zagotovi baterijo, sam IC pa je varen.
IC ima funkcijo za zaščito pred temperaturo znotraj, ko je notranja temperatura čipa previsoka, bo izklopila izhod, temperaturna histereza še naprej deluje.
Izhod za LED prikazovalnika prikazuje stanje polnjenja.
Na voljo v paketu SOP-8.-----------------------
Angleški prevod zgornjega kitajskega linka:
I. OverviewAsc0301 as a USB NICD/nimh battery charge management ICS for applications in NICD/nimh battery USB charger.
The chip is a high-efficiency, control, reliable charge management circuit. The entire circuit detects the battery voltage control charging current size. Circuit has 0 -V and -V -a fast charge termination method, ensure that the battery is charging a rate of 100%. Chip Design with a built-in high-precision ADC to sample the battery voltage and current for analog-to-digital conversion, and output digital signal to the arithmetic logic unit test, a reliable way to terminate the fast charge.
II. The product features1, to the nicd/nimh battery Section 1 - 8, a rechargeable battery.
2, the chip operating voltage of 5V, supply a range of 2.6V to 7.5V.
3, chip design with built-in to the 10bit ADC sampling of battery voltage and current for analog-to-digital conversion, and output digital signal to the arithmetic logic unit test.
4, charging for the use of 0 -V- -V detection method.
5, IC, the built-in automatic current regulator, when the Boost voltage increases to a maximum or input voltage is low with the current automatic adjustment function, the current automatic adjustments in the current to a maximum current.
6, IC, with the output short circuit alarm function to keep the battery, and IC for their own safety.
7, IC, with internal over-temperature protection function, when the chip is the internal temperature is too high, the output is switched off, the temperature lag after return to work.
8, the drive LED output shows the charge status.
9, A SOP8 package.
III. The typical applicationsCB5121_nacrt.jpg
The three sections nicd/nimh battery management circuit diagram
Note: You do not need the EMC certification requirements, you can remove the L2, L3, use wire to bypass.
IV. Chip pin definitionPin name Features
1 VCC USB power
2 PD output P-channel FET DRAIN OUTPUT (PWM buck controller output)
3 ND output N-channel FET DRAIN OUTPUT (PWM boost controller output), the)
4 LED output A status indicator (4 state: On/Off/slow 1HZ/FLASH 10HZ)
5 VREF Internal AD reference ground
6 AD_V input Battery voltage detection port
7 AD_I input Charge current detection port
8 GND Power ground
V. Functional Description1, ASC0301 can charge NiCad / NiMH rechargeable batteries 1-8, 1 -8 batteries must be selected when charging the correct configuration, R3 and R2 corresponding configuration and R4 reference resistance as shown below Show:
The number of batteries Configuration ratio R3: R2 R4 (Ω)
__________________________________________________________
Tukaj glej tabelo na kitajskem viru !2, LED indicator:
Indicator status Corresponding circuit status
__________________________________________________
Always light = That connected to the power is not charging
Slow flash (frequency of 1HZ) = Indicates normal charge
Flash (frequency is 10HZ) = Indicates that the output is shorted or the battery pack number does not match the circuit
Extinguished = Indicates the battery is full
3, USB power protection:
When charging multiple batteries, USB power is required to provide a large current. To ensure that no USB power is damaged, the ASC0301 adds USB power protection. When the USB power supply voltage is pulled down to a certain threshold, reduce the charging current to protect the safety of the USB power supply, and then adjust the charging current to the maximum value when the USB power supply voltage rises.
4, short circuit protection and zero-volt battery activation:
The ASC0301 intelligently detects if the output is shorted and indicates an error. The ASC0301 allows output short circuits for long periods of time without damaging any of the circuits and the USB power supply while the output is short-circuited and maintains low power consumption.
The ASC0301 has a zero volt battery activation feature that determines zero volts at the first short circuit detected after power-up. Zero-volt battery will be activated immediately, zero-volt battery activated into the normal charging process. If the zero-volt battery can not be activated, will determine the short circuit, the light starts flashing.
5, battery protection function:
(1) If the battery voltage is higher than 1.35V, think the battery is close to the full capacity, do not charge after plugging in, and the indicator goes out to prevent the battery capacity from decreasing due to the memory effect of the NiCd battery.
(2) Battery access will determine the number of battery pack, if the voltage is not within the corresponding range, do not charge.
VI. charging process:(1) battery insertion detection.
When the charger is powered on, it will automatically detect whether the battery is inserted. After the zero volt battery is detected, it will be activated automatically. If a short circuit is detected, an error will be indicated. If the number of detected battery packs does not match with the circuit, an error will be reported. After the correct battery pack is inserted, normal charging is detected.
(2) Pre-charge.
If the battery connected to a single battery is less than 1V, it indicates that the battery discharge too much, need a small current activation before charging to prevent damage to the battery. Pre-charge the need to control the current at 100mA, when the single-cell battery voltage is greater than 1V into the fast charge.
(3) quick charge.
If you connect the battery pack has been more than 1V battery, it indicates that the battery charge has passed the pre-charge threshold, you can quickly charge. Fast charge requires current control at 250mA. Fast charging process should be timed to detect the battery voltage and charging current, detected battery voltage-Δv or 0 △ V, jump to make up the charge.
(4) make up the charge.
Fast Charge After the battery voltage has been charged to 1.3V with a large current, the battery temperature will increase quickly if it is re-charged quickly. The current needs to be charged to a small current of 200 mA. Make up for 20 minutes charging time, make up after the end of charging jump to trickle charge.
(5) trickle charge.
To make up for the battery self-discharge, make up after the end of charging into trickle charge, trickle charge current of 40mA. Into the trickle charge indicator light has been extinguished, when the user removed the battery into the next charge cycle.
(6) take the battery test.
When entering the charge, the system will always take the battery away from the test, to detect the battery removed, it will enter the next charge cycle.
Nimate dovoljenj za ogled prilog tega prispevka.